![]() Question: Do I receive a GST applied bill?Īnswer: Yes. Connectors pin once locked afterwards can’t remove separately. ![]() Question: Is it reusable?Īnswer: It’s not reusable. Question: Is it suitable 10mm wire?Īnswer: No sir, it is suitable for up to 6 sq. To avoid any electric shock during assembly / installation, make sure that the solar panel is not exposed to sunlight or covered to block any solar radiation.įAQs of Mc4 Connector Question: Is it suitable for 6sq mm cable?Īnswer: Yes, It is suitable for 2.5mm, 4mm and 6mm solar DC wires. When the surface of the solar panel is exposed to sunlight, a DC voltage appears at the output voltage that turns it into a live voltage source that can produce electric shock. Stay safe and thanks for visiting our MC4 connection guide. When the sun is on your solar panels or they are connected to a battery, you may be injured by your solar power. Please remember to never disconnect the connectors. This will confirm that you have a good connection that will last for years. I would recommend testing the continuity of your cable with new MC4 connectors before connecting it to your solar panels or charge controller. Tighten the nut on the female plastic housing on the test. Step 7: Insert the CableĬheck the rubber washer in step 5, and then push the crimped cable into the female housing until you hear “CLICK”. Crimp like a male in step 2 when inserting cable. This cable insulation is stripped of 15 mm to expose the wire for crimping. We twisted the cable slightly for better surface contact inside the crimp. If you do not do this with a 4 mm cable, the connector will be able to move around the cable and over time may damage the connection on the female connector. This will give the best grip on the 4mm cable when tightening the nut on the plastic housing. Taking a closer look at the picture you will see that the rubber seal washer is flush with the end of the plastic fingers around the cable. This is a non-return clip to the lock that folds into the plastic housing to check the rubber washer. When you push the crimped cable into the connector, you will hear the “CLICK” sound. There is a non return clip inside the plastic housing and if you have not placed the nut on the cable you will not be able to damage it without damaging the plastic housing and it will be unsafe to use when inserting the cable. ![]() It is easy way to connect to Mc4 connectors. The crimping tool is available on the internet (Amazon) for just approx Rs. Using of the MC4 connector 2.5mm, 4mm and 6mm crimp connector for this as it gives a great connection every time and holds all the bits when you crimp. The recommended cable stripping length on crimping is between 10 and 15 mm. If your cable increases this mark in the connector, you will not be able to connect the MC4 connectors together. There is a mark on the metal to indicate how far the other connectors will penetrate into it. You will notice that the wire is shorter compared to the metal crimping connector. Kenbrook Solar MC4 Female Wire Connector Kenbrook Solar MC4 Male Wire Connector Step 1: Male MC4 Connector Fitting Ensure that no current is flowing when unplugging is attempted. To uncheck the two connectors, press the ends of the locking tabs as they appear in the open locking slot to release the locking mechanism and pull the connectors apart. When the two connectors are locked, the locking tabs slide into the locking slot and are secured. Push the two connector pairs together such that the two locking tabs on the MC4 female connector align with the two corresponding locking slots on the MC4 male connector. The solar MC4 wire connectors work best with all types of DC wires, when you buy any new solar panel (usually over 30 Watts) it will be already fitted MC4 connectors attached for you to get the power safely out of the solar panel and preventing of electric shock. Now, Solar Mc4 Connector do not connect with older MC3 type connectors. Now it come on all new solar panels, providing an IP67 waterproof and dust proof secure electrical connection. They are UV protected and weather resistant. We have high quality MC4 wire Connector long life Lifespan. But you need a device to disconnect them, and make sure that they don’t accidentally disconnect when cables are pulled. ![]() The Solar MC4 connector allows for easy construction by pushing the connectors from the side panel together by hand. Solar Mc4 Connector commonly used for connecting solar panels and are single contact electric Mc4 connector. MC4 stands for the “Manufacturer Multi Contact”. The Solar Mc4 wire Connector make solar panel connection each other very simple. There is a pair (male and female) of connectors in which one is male connector and second is female connector. Solar MC4 Connectors are used for connect the solar panel each other with very simply way. 250 Liter Solar Water Heater With Complete Details. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |